Pololu Crimping Tool for 0.1 to 1.0mm2 Capacity 16-28 AWG Wires

Top rated

Pololu

Pololu Crimping Tool for 0.1 to 1.0mm2 Capacity 16-28 AWG Wires

SKU: PO1928

4.5 / 2 reviews

71,34 €

per pack

incl. 19% VAT plus

Net: 59,95 €

Choose tax zone / country of delivery

From

Unit price / pack

71,34 € (Net: 59,95 €)

67,06 € (Net: 56,35 €)

63,03 € (Net: 52,97 €)

Product customisation & sourcing & PCBA one-stop service are available with us.

Request personal offer!

Available immediately

Delivery time: 11 - 13 Workdays (DE - int. shipments may differ)

Product Information

Product safety information

Manufacturer information:

Pololu Corporation
Pilot Rd. 920
Nevada
Las Vegas, Vereinigte Staaten, 89119
[email protected]
https://www.pololu.com/

Responsible person:

Eckstein GmbH
Am Ostbahnhof 3
Niedersachsen
Clausthal-Zellerfeld, Deutschland, 38678
[email protected]
https://eckstein-shop.de

Dimensions and Weight
GTIN:	4060137049118
HAN:	1928
Category:	Button/Miscellaneous
Storage Tiers:	Maintain
Shipping weight:	0,44 kg
Item weight:	0,37 kg
Dimensions ( Length × Width × Height ):	15,00 × 10,00 × 5,00 cm

Product Description

This crimping tool can be used to crimp both male and female versions of our Tamiya connector crimp pins, mini Tamiya connector crimp pins, JST RCY connector crimp pins, JR crimp pins, Futaba J crimp pins, and crimp pins for 0.1″ housings onto 16-28 AWG wires to make custom cables. The crimping die has a width of 7 mm, and the tool offers ratcheting action for increased consistency and ease of use.

Using the Crimping Tool

Prepare the wire by stripping about 1/8" (3 mm) of insulation from the end. Place the wire in the crimp pin, lining it up so that the stripped portion lies between the inner set of tabs on the crimp pin, while insulated wire lies between the outer set of tabs.

Tip: Instead of removing the crimp pin from the reel by breaking it off at the base (as intended), it can be helpful to leave a small tab on the back of the crimp pin to help you line it up and hold it in place while crimping, as shown in the pictures below. Then, you can remove the tab after it is crimped.

Place the wire and crimp pin on the appropriate tooth of the tool’s die, making sure that the insulated end is on the raised and wider half of the tooth. The tabs should point toward the cavity on the other side of the die so that the tool bends them inward around the wire when it closes.

Close the jaws of the tool slowly and completely until they release. The tabs on a properly crimped pin should form one barrel around the wire conductors and another barrel for strain relief around the wire insulation.

Average item rating

Share your experiences with other customers!

All reviews:

How do reviews work?

Total entries: 2

21.10.2018 Verified purchase

Pololu Crimping Tool 0.1-1.0 mm² Capacity, 16-28 AWG Werkzeug

Sehr gute Beschreibung auf der Bestellseite. Gute Verarbeitung. Liegt gut in der Hand und kann einhändig zu benutzen werden. Presst die Kontakte ohne Probleme und sauber.
Beschreibung auf Crimpzange von - bis wäre wünschenswert. Die Liste hat man nicht immer zur Hand!

René H

27.05.2019 Verified purchase

Som beskrevet

Kvalitetsværktø.j

Karl S

Video Tutorial

Check Points for Correct Crimping

Manufacturer according to GPSR
Pololu Corporation, Pilot Rd. 920, 89119 Las Vegas, Nevada, Vereinigte Staaten, [email protected], https://www.pololu.com/
Responsible person according to GPSR
Eckstein GmbH, Am Ostbahnhof 3, 38678 Clausthal-Zellerfeld, Niedersachsen, Deutschland, [email protected], https://eckstein-shop.de

Cookiename	Beispielinhalt	Ablaufzeit
_ga_*	deleted	730 Tage
_ga	GA1.1.8643343795.1726666186	730 Tage

Pololu Crimping Tool for 0.1 to 1.0mm2 Capacity 16-28 AWG Wires

Dimensions and Weight

Pololu Crimping Tool 0.1-1.0 mm² Capacity, 16-28 AWG Werkzeug

Som beskrevet

Video Tutorial

Check Points for Correct Crimping

Pololu Crimping Tool for 0.1 to 1.0mm2 Capacity 16-28 AWG Wires

Service package

Services for business customers