Pololu 3.3V, 3.6A Step-Down Voltage Regulator D36V28F3

+ 2

show

Pololu

Pololu 3.3V, 3.6A Step-Down Voltage Regulator D36V28F3

SKU: PO3781

18,95 €

per pack

incl. 19% VAT plus

Net: 15,92 €

Choose tax zone / country of delivery

Product customisation & sourcing & PCBA one-stop service are available with us.

Request personal offer!

Available immediately

Delivery time: ca. 3 weeks (DE - int. shipments may differ)

This small synchronous switching step-down (or buck) regulator takes an input voltage from 4.5 V to 50 V and efficiently reduces it to 3.3 V. The board measures only 0.7" × 0.8" yet delivers typical maximum continuous output currents between 3.2 A and 4.5 A, depending on the input voltage, which makes it well suited for powering moderate loads like sensors or small motors. More product details

Product Information

Product safety information

Manufacturer information:

Pololu Corporation
Pilot Rd. 920
Nevada
Las Vegas, Vereinigte Staaten, 89119
[email protected]
https://www.pololu.com/

Responsible person:

Eckstein GmbH
Am Ostbahnhof 3
Niedersachsen
Clausthal-Zellerfeld, Deutschland, 38678
[email protected]
https://eckstein-shop.de

Dimensions and Weight
GTIN:	4060137056635
HAN:	3781
Category:	Step-Down
Regulator-Function:	Step-Down
Output-Type:	fixed
Output Voltage:	3.3V
Operating Voltage max.:	50V
Operating Voltage min.:	4.5V
Continuous Output Current:	3.6A
Quiescent Current max.:	3mA
Storage Tiers:	Maintain
Shipping weight:	0,01 kg
Item weight:	0,01 kg
Dimensions ( Length × Width × Height ):	1,80 × 2,10 × 0,90 cm

Product Description

Overview

The D36V28Fx family of buck (step-down) voltage regulators generates lower output voltages from input voltages as high as 50 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters), which makes them much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. These regulators can typically support continuous output currents between 2 A and 4 A, depending on the input voltage and output voltage. In general, the available output current is a little higher for the lower-voltage versions than it is for the higher-voltage versions, and it decreases as the input voltage increases.

The regulators have reverse voltage protection up to 40 V, output undervoltage and overvoltage protection, over-current protection, and short-circuit protection. A thermal shutdown feature also helps prevent damage from overheating and a soft-start feature limits the inrush current and gradually ramps the output voltage on startup.

Technical Details

Input voltage: 4.5 V to 50 V (minimum input subject to dropout voltage considerations for currents over 4 A)
Output voltage: 3.3 V with 4% accuracy
Typical maximum continuous output current: 3.2 A to 4.5 A
Typical efficiency of 80% to 90%, depending on input voltage, output voltage, and load
Switching frequency: ~500 kHz under heavy loads
Power-save mode with ultrasonic operation that increases light load efficiency by reducing switching frequency, but keeps it above the audible range (20 kHz)
2 mA to 3 mA typical no-load quiescent current
Enable input for disconnecting the load and putting the regulator into a low-power state that draws approximately 10 µA to 20 µA per volt on VIN
"Power good" output indicates when the regulator cannot adequately maintain the output voltage
Output undervoltage and overvoltage protection
Soft-start feature limits inrush current and gradually ramps output voltage
Integrated reverse-voltage protection up to 40 V, over-current and short-circuit protection, over-temperature shutoff
Compact size: 0.7" × 0.8" × 0.345" (17.8 mm × 20.3 mm × 8.8 mm)
Two 0.086" mounting holes for #2 or M2 screws

Dimension

Size: 0.7" × 0.8" × 0.345"¹
Weight: 3.3 g¹

Specification

Minimum operating voltage: 4.5 V²
Maximum operating voltage: 50 V
Continuous output current: 3.6 A³
Output voltage: 3.3 V
Reverse voltage protection?: Y⁴
Maximum quiescent current: 3 mA⁵
Output type: fixed 3.3V

Notes:

Without included optional headers.
Subject to dropout voltage considerations. See the dropout voltage graph under the description tab for more information.
Typical continuous output current at 36 V in. Actual achievable continuous output current is a function of input voltage and is limited by thermal dissipation. See the output current graph under the description tab for more information.
To -40 V. Connecting supplies over 40 V in reverse can damage the device.
While enabled with no load. Can be reduced to under 1 mA using the enable pin.

Package List

1x Pololu 3.3V, 3.6A Step-Down Voltage Regulator D36V28F3

Write the first review for this item and help others make a purchase decision!

Dimension diagram of the Step-Down Voltage Regulator D36V28Fx

Manufacturer according to GPSR
Pololu Corporation, Pilot Rd. 920, 89119 Las Vegas, Nevada, Vereinigte Staaten, [email protected], https://www.pololu.com/
Responsible person according to GPSR
Eckstein GmbH, Am Ostbahnhof 3, 38678 Clausthal-Zellerfeld, Niedersachsen, Deutschland, [email protected], https://eckstein-shop.de

Cookiename	Beispielinhalt	Ablaufzeit
_ga_*	deleted	730 Tage
_ga	GA1.1.8643343795.1726666186	730 Tage

Pololu 3.3V, 3.6A Step-Down Voltage Regulator D36V28F3

Dimensions and Weight

Dimension diagram of the Step-Down Voltage Regulator D36V28Fx

Pololu 3.3V, 3.6A Step-Down Voltage Regulator D36V28F3

Service package

Services for business customers