WaveShare ST-LINK/V2 (mini) STM8 STM32 Programmers Debuggers

Artikelnummer: WS10053

EAN: 4060137059070

HAN: 10053

Herkunftsland: CN

Kategorie: STM8


7,99 €

inkl. 19% USt.,

10 Pack auf Lager

Lieferfrist: ca. 1 - 2 Tage

Pack


Beschreibung

Description

Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.

Features

  • Onboard 500mA self-recovery fuse to avoid harming by short circuit
  • Dual voltage output (3.3V/5V), easy for debugging/programming
  • Standard USB interface for direct connection to PC
  • Debugging/Programing performance
    • Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
    • Programming : supports FLASH ROM, EEPROM, AFR, etc.
    • USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
  • Upgradable firmware
    • The firmware is upgradable to support more devices in the future
    • Automatically upgraded
  • Supported software
    • ST-LINK Utility v2.0 (or higher ver.)
    • STVD Version 4.2.1 (or higher ver.)
    • STVP Version 3.2.3 (or higher ver.)
    • IAR EWARM Revision v6.20 (or higher ver.)
    • IAR EWSTM8 Revision v1.30 (or higher ver.)
    • KEIL RVMDK Revision v4.21 (or higher ver.)
    • ATOLLIC
    • TASKING
  • Supported devices
    • All the STM8 devices with SWIM interface
    • All the STM32 devices with SWD interface

ST-LINK/V2 (mini) Vs ST-LINK/V2 Vs ST-LINK

COMPAREST-LINK/V2 (MINI)ST-LINK/V2ST-LINKREMARKS
SWD voltage range1.65V - 3.6V1.65V - 3.6V3V - 3.6VST-LINK/V2 and ST-LINK/V2 (mini) support STM32 low voltage devices
SWIM voltage range1.65V - 5.5V1.65V - 5.5V1.65V - 5.5V
Supports SWVNOYESNOFor the moment, only STM32 supports SWV while STM8 doesn't
Debug interfaces221ST-LINK/V2 and ST-LINK/V2 (mini) support STM8/STM32 with separated interfaces
LED indicatorDual color LEDDual color LEDRed LEDDual color LED allows indicating more status
FuseYESNONOFuse for avoid harming by short circuit

Connection with STM8/STM32 applications

The ST-LINK/V2 (mini) should be connected to the STM8 application via the SWIM interface.

DEBUGGER PINTARGET BOARD PINDESCRIPTION
VCCMCU VCCSTM8 VCC
SWIMMCU SWIMSTM8 SWIM PIN
GNDGNDSTM8 GND
RSTMCU RESETSTM8 RESET PIN

The ST-LINK/V2 (mini) should be connected to the STM32 application via the SWD interface.

DEBUGGER PINTARGET BOARD PINDESCRIPTION
VCCMCU VCCSTM32 VCC
SWDIOMCU SWDIOSTM32 SWD SWDIO
GNDGNDSTM32 GND
SWCLKMCU SWCLKSTM32 SWD SWCLK

Please note that the VCC and GND should be connected correctly to avoid any harm to the ST-LINK/V2 (mini).

Dokumente

Wiki

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

----