Pilot Rd. 920
Nevada
Las Vegas, Vereinigte Staaten, 89119
[email protected]
https://www.pololu.com/
Am Ostbahnhof 3
Niedersachsen
Clausthal-Zellerfeld, Deutschland, 38678
[email protected]
https://eckstein-shop.de
GTIN: | 4060137048623 |
HAN: | 2999 |
Category: | Gear Motor Driver |
Storage Tiers: | Maintain |
Shipping weight: | 0,01 kg |
Item weight: | 0,01 kg |
Dimensions ( Length × Width × Height ): | 3,00 × 2,50 × 0,30 cm |
Overview
The TB67H420FTG from Toshiba is an H-bridge motor driver IC that can be used for bidirectional control of one or two brushed DC motors at 10 V to 47 V. It can supply up to about 1.7 A continuously to each of two separate motors or about 3.4 A to a single motor, and it can tolerate peak currents up to 4.5 A per channel (dual) or 9 A (single) for a few seconds, making it a good choice for small- to medium-sized motors that run at higher voltages. The TB67H420FTG is a great IC, but its small surface-mount package makes it difficult for the typical student or hobbyist to use; our breakout board makes it easy to use with standard solderless breadboards and 0.1? perfboards. Since this board is a carrier for the TB67H420FTG, we recommend careful reading of the TB67H420FTG datasheet (460k pdf). The board ships populated with SMD components, including the TB67H420FTG and a reverse battery protection circuit.
Features
- Single- or dual-channel H-bridge motor driver (can drive one or two DC motors)
- Motor supply voltage: 10 V to 47 V
- Output current:
- up to 1.7 A continuous (4.5 A peak) per motor in dual-channel mode
- up to 3.4 A continuous (9 A peak) in single-channel mode
- Configurable current chopping actively limits motor current to 4.5 A per channel (dual) or 9 A (single) by default; can be lowered with external resistors or voltage sources
- No separate logic supply needed; inputs are 3V- and 5V-compatible
- Flexible input interface provides several options for control
- Under-voltage lockout and protection against over-current/short-circuit and over-temperature
- Open-load detection
- Carrier board adds reverse-voltage protection up to 40 V
- Active-low error outputs indicate over-current, over-temperature, or open-load condition
- Compact size (1.0? × 1.2?)
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
Note: the motor supply capacitors on this carrier are rated for 50 V; this is less margin than on most of our motor driver carriers, which have ICs with ratings of 40 V or less. Please keep this in mind if you want to push the high-voltage limit of this driver.
Dimensions
- Size:1.2? × 1.0?1
- Weight:3.5 g1
General specifications
- Motor driver:TB67H420FTG
- Motor channels:2
- Minimum operating voltage:10 V
- Maximum operating voltage:47 V2
- Continuous output current per channel:1.7 A
- Continuous paralleled output current:3.4 A
- Reverse voltage protection?:Y2
Identifying markings
- PCB dev codes:md35a
- Other PCB markings:0J11169
Notes:
- 1.Without included hardware.
- 2.Note: Reverse voltage protection only works up to 40 V.
User` Guide
Toshiba TB67H420FTG datasheet
Schematic diagram
Dimension diagram
3D model
Drill guide
Manufacturer according to GPSR
Pololu Corporation, Pilot Rd. 920, 89119 Las Vegas, Nevada, Vereinigte Staaten, [email protected], https://www.pololu.com/
Responsible person according to GPSR
Eckstein GmbH, Am Ostbahnhof 3, 38678 Clausthal-Zellerfeld, Niedersachsen, Deutschland, [email protected], https://eckstein-shop.de