Pololu Carrier for MQ Gas Sensors (Bare PCB Only)

Pololu

Pololu Carrier for MQ Gas Sensors (Bare PCB Only)

SKU: PO1479

2,25 €

per pack

incl. 19% VAT plus

Net: 1,89 €

Choose tax zone / country of delivery

Request personal offer!

Available immediately

Delivery time: ca. 3 weeks (DE - int. shipments may differ)

This carrier board is designed to work with any of the MQ-series gas sensors, simplifying the interface from 6 to 3 pins—ground, power and analog voltage output—that are broken out with a 0.1" spacing, making the board compatible with 0.1" headers and standard breadboards and perfboards. This board has two mounting holes and provides convenient pads for mounting the gas sensor’s required sensitivity-setting resistor. More product details

Description
Reviews

Product Information

Product safety information

Manufacturer information:

Pololu Corporation
Pilot Rd. 920
Nevada
Las Vegas, Vereinigte Staaten, 89119
[email protected]
https://www.pololu.com/

Responsible person:

Eckstein GmbH
Am Ostbahnhof 3
Niedersachsen
Clausthal-Zellerfeld, Deutschland, 38678
[email protected]
https://eckstein-shop.de

Dimensions and Weight
GTIN:	4060137099984
HAN:	1479
Category:	Power/Miscellaneous
Shipping weight:	0,01 kg
Item weight:	0,01 kg

Product Description

Overview

This breakout board is designed to work with any of the MQ-series gas sensors, simplifying the interface from 6 to 3 pins—ground, +5V VCC, and an analog voltage output—that are broken out with a 0.1"" spacing, making the board compatible with 0.1"" headers and standard breadboards and perfboards. This board has two mounting holes and provides convenient pads for mounting the gas sensor’s required sensitivity-setting resistor (referred to as RL in the sensor datasheet). All of the board’s traces are on the same side of the PCB, making it easy to see how the pads are connected.

The two mounting holes are intended to be used with #2 screws (not included).

Note that we also offer an alternate gas sensor breakout board that is more compact, with a diameter equal to that of the smaller gas sensor and the broken-out pins beneath the sensor.

Connections

Connect VCC to 5 V, GND to ground, and OUT to an analog-to-digital converter (ADC). The board has two pairs of through-hole pins for the required (but not included) sensitivity-selecting resistor RL, providing two mounting options—horizontal or vertical—between GND and OUT as shown in the pictures below. The resistance of RL should be calculated using the datasheet for your particular gas sensor.

The MQ gas sensors have light to no polarity, so the gas sensor will work with the board all four ways it fits into the 6 pins (there are two possible orientations on each side of the board).

The picture to the right above shows a board with a 3×1 0.1"" right-angle male header soldered to it, which allows a standard servo cable to be used to connect the board to your project.

Note: This product consists of the PCB by itself; it does not include a gas sensor, sensitivity resistor, header pins, or any additional hardware.

Write the first review for this item and help others make a purchase decision!

Manufacturer according to GPSR
Pololu Corporation, Pilot Rd. 920, 89119 Las Vegas, Nevada, Vereinigte Staaten, [email protected], https://www.pololu.com/
Responsible person according to GPSR
Eckstein GmbH, Am Ostbahnhof 3, 38678 Clausthal-Zellerfeld, Niedersachsen, Deutschland, [email protected], https://eckstein-shop.de

Cookiename	Beispielinhalt	Ablaufzeit
_ga_*	deleted	730 Tage
_ga	GA1.1.8643343795.1726666186	730 Tage

Pololu Carrier for MQ Gas Sensors (Bare PCB Only)

Dimensions and Weight

Overview

Connections

Pololu Carrier for MQ Gas Sensors (Bare PCB Only)

Service package

Services for business customers