Pololu 6V, 2.5A Step-Down Spannungsregler D24V25F6

Pololu

Pololu 6V, 2.5A Step-Down Spannungsregler D24V25F6

SKU: PO2852

22,55 €

per pack

incl. 19% VAT plus

Net: 18,95 €

Choose tax zone / country of delivery

Product customisation & sourcing & PCBA one-stop service are available with us.

Request personal offer!

Available immediately

Delivery time: 2 - 3 weeks (DE - int. shipments may differ)

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38V and efficiently reduces it to 6V. The board measures only 0.7"x0.7", but it allows a typical continuous output current of up to 2.5A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors. High efficiencies are maintained at light loads by dynamically changing the switching frequency, and an optional shutdown pin enables a low-power state with a current draw of a few hundred microamps. More product details

Product Information

Product safety information

Manufacturer information:

Pololu Corporation
Pilot Rd. 920
Nevada
Las Vegas, Vereinigte Staaten, 89119
[email protected]
https://www.pololu.com/

Responsible person:

Eckstein GmbH
Am Ostbahnhof 3
Niedersachsen
Clausthal-Zellerfeld, Deutschland, 38678
[email protected]
https://eckstein-shop.de

Dimensions and Weight
GTIN:	4060137016127
HAN:	2852
Category:	Step-Down
Regulator-Function:	Step-Down
Output-Type:	fixed
Output Voltage:	6V
Operating Voltage max.:	38V
Operating Voltage min.:	7V
Continuous Output Current:	2.5A
Quiescent Current max.:	0.7mA
Storage Tiers:	Maintain
Shipping weight:	0,01 kg
Item weight:	0,01 kg
Dimensions ( Length × Width × Height ):	1,80 × 1,80 × 0,90 cm

Product Description

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 6 V. The board measures only 17.8 mm × 17.8 mm, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors. High efficiencies are maintained at light loads by dynamically changing the switching frequency, and an optional shutdown pin enables a low-power state with a current draw of a few hundred microamps.

Features

Input voltage:
- 4.5 V to 38 V for the version that outputs 3.3 V
- [output voltage + dropout voltage] to 38 V for output voltages of 5 V and higher (see below for more information on dropout voltage)
Fixed 3.3 V, 5 V, 6 V, 7.5 V, or 9 V output (depending on regulator version) with 4% accuracy
Typical maximum continuous output current: 2.5 A
Integrated reverse-voltage protection, over-current and short-circuit protection, over-temperature shutoff, and soft-start
Typical efficiency of 85% to 95%, depending on input voltage and load; the switching frequency automatically changes at light loads to maintain high efficiencies
Typical no-load quiescent current under 1 mA; can be reduced to 10 µA to 20 µA per volt on VIN by disabling the board
Two 0.086? mounting holes for #2 or M2 screws
Compact size: 17.8 mm × 17.8 mm × 9 mm
Weight: 2.6 g (Without included optional headers.)

General specifications

Minimum operating voltage: 7 V (For small loads; this voltage rises approximately linearly up to around 7.4 V at 2.5 A output.)
Maximum operating voltage: 38 V
Output voltage: 6 V
Reverse voltage protection?: Y
Maximum quiescent current: 0.7 mATypical worst case. (The ENABLE pin can be used to reduce the quiescent current to a few hundred microamps.)

Identifying markings

PCB dev codes: reg15a
Other PCB markings: 0J8475

Write the first review for this item and help others make a purchase decision!

Bedienungsanleitung

Manufacturer according to GPSR
Pololu Corporation, Pilot Rd. 920, 89119 Las Vegas, Nevada, Vereinigte Staaten, [email protected], https://www.pololu.com/
Responsible person according to GPSR
Eckstein GmbH, Am Ostbahnhof 3, 38678 Clausthal-Zellerfeld, Niedersachsen, Deutschland, [email protected], https://eckstein-shop.de