Pololu 2.5-9V Fine-Adjust Step-Up/Step-Down Voltage Regulator w/ Adjustable Low-Voltage Cutoff S9V11MACMA

Artikelnummer: PO2868

The S9V11MACMA switching step-up/step-down regulator efficiently produces a finely adjustable output between 2.5 V and 9 V whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has a precision-adjustable low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge. The compact (0.5? × 0.6?) module can supply a typical output current of up to 1.5 A when the input voltage is close to the output voltage.

Kategorie: Step-Up/Step-Down Spannungregler


11,95 €

inkl. 19% USt.,

1 Packung auf Lager

Lieferfrist: ca. 1 - 3 Tage

Packung


Beschreibung

The S9V11x family of efficient switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) use a buck-boost topology to convert both higher and lower input voltages to a regulated output voltage. They take input voltages from 2 V to 16 V and increase or decrease them as necessary, offering a typical efficiency of over 85% and a typical output current of up to 1.5 A. The flexibility in input voltage offered by this family of regulators is especially well-suited for battery-powered applications in which the battery voltage begins above the regulated voltage and drops below as the battery discharges. Without the typical restriction on the battery voltage staying above the required voltage throughout its life, new battery packs and form factors can be considered.

The different members of this family offer different output voltage options, from fixed voltages with selectable alternatives to adjustable voltages that can be set anywhere between 2.5 V and 9 V using a precision 12-turn potentiometer. Some versions also have an adjustable low-voltage cutoff that can be set anywhere in the 2 V to 16 V output voltage range and used to prevent your battery from over-discharging. This is particularly useful for battery chemistries that can be damaged when over-discharged, including Li-ion and LiPo.

 

These regulators have short-circuit protection, and thermal shutdown prevents damage from overheating; they do not have reverse-voltage protection. Note that the startup current is limited to approximately 700 mA until the output voltage reaches the nominal voltage; after startup, the available current is a function of the input voltage (see the Typical efficiency and output current section below).

Features

  • Input voltage: 2 V to 16 V (note: this regulator requires 3 V to start, but it can operate down to 2 V after startup)
  • Output voltage: 2.5 V to 9 V (precision-adjustable using built-in 12-turn potentiometer)
  • Typical maximum continuous output current: 1.5 A (when input voltage is close to the output; the Typical efficiency and output current section below shows how the achievable continuous output current depends on the input and output voltages)
  • Precision-adjustable low-voltage cutoff with hysteresis can be used to protect batteries from over-discharging (quiescent current is approximately 10 µA per volt on VIN when regulator is disabled)
  • Power-good indicator can be used to tell when the regulator has reached and is maintaining its target output voltage
  • Power-saving feature maintains high efficiency at low currents (quiescent current is less than 1 mA while enabled)
  • Integrated over-temperature and short-circuit protection
  • Small size: 0.5? × 0.6? × 0.25? (12.7 × 15.3 × 6.4 mm)

During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.

Connections

The step-up/step-down regulator has five main connections all located along the same edge of the board: the output voltage (OUT), ground (GND), the input voltage (IN), an enable input (EN), and a power good indicator (PG). The board also contains a through-hole labeled SEL that is not used on this version of the regulator.

 

The input voltage, VIN, should be between 3 V and 16 V when the regulator is first powered. After it is running, it can continue operating down to 2 V. Lower inputs can shut down the voltage regulator; higher inputs can destroy the regulator, so you should ensure that noise on your input is not excessive, and you should be wary of destructive LC spikes (see below for more information).

The regulator features an enable pin, EN, that can be used as a precision low-voltage cutoff thanks to its tight activation and deactivation thresholds (voltages below 0.7 V trigger a low-power sleep state, and voltages above 0.8 V re-enable the regulator). On this regulator version, EN is connected to VIN through a 12-turn potentiometer to provide a user-adjustable cutoff threshold, which is useful for battery powered applications where draining the battery below a particular voltage threshold could permanently damage it. The quiescent current draw in this sleep mode is dominated by the current in the resistor network from ENABLE to VIN, which is approximately 10 µA per volt on VIN (e.g. approximately 30 µA with 3 V in). See the Setting the cutoff voltage section below for details on how to use the built-in potentiometer to set the cutoff threshold.

The ?power good? indicator, PG, is an open-drain output that goes low when the regulator?s output falls below around 90% of the nominal voltage, including when the enable pin is held low. The power good indicator is held low until the output reaches 95% of the nominal voltage when it is powering up or coming out of low-power mode. Otherwise, the PG pin is high-impedance, so an external pull-up resistor is required to use this pin.

Dimensions

Size: 0.5"× 0.6" × 0.25"
Weight: 1.0 g

General specifications

Minimum operating voltage: 2 V
Maximum operating voltage: 16 V
Maximum output current: 1.5 A
Minimum output voltage: 2.5 V
Maximum output voltage: 9 V
Reverse voltage protection?: N
Maximum quiescent current: 1 mA
Low-voltage cutoff: adjustable

Dokumente

Diemension

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

----

Kunden kauften dazu folgende Produkte
LM2596S DC-DC einstellbarer Step-Down Spannungsregler... LM2596S DC-DC einstellbarer Step-Down Spannungsregler...
100 Packung auf Lager
NodeMcu Lua WIFI Internet Development Board based on... NodeMcu Lua WIFI Internet Development Board based on...
170 Packung auf Lager
PAM8403 Volume Adjustment 2-Kanal Digital Amplifier... PAM8403 Volume Adjustment 2-Kanal Digital Amplifier...
28 Packung auf Lager
Adafruit USB Micro-B Breakout Board Adafruit USB Micro-B Breakout Board
8 Packung auf Lager
Pololu Adjustable 4-12V Step-Up Spannungsregler U3V50ALV Pololu Adjustable 4-12V Step-Up Spannungsregler U3V50ALV
1 Packung auf Lager