OpenArm 1.0 Follower (Dual-Arm) – Complete System, Pre-Assembled & Tested
Pre-assembled · tested · backdrivable joints × bidirectional force feedback × optional D435 chest and D405 wrist cameras
Overview
OpenArm is an open-source 7-DOF humanoid robot arm project for Physical AI research. Hardware, control code and simulation tools are publicly available, with an emphasis on high backdrivability, compliance and deployment in contact-rich tasks. OpenArm 1.0 is the mature platform version of the project: human-scale structure, DAMIAO QDD direct-drive motors, backdrivable joints with mechanical limits, and real-time feedback of position, velocity, torque, temperature and fault status.
The OpenArm 1.0 Follower is the execution-side system in a leader-follower setup, delivered as a pre-assembled, internally wired and basic-function-tested dual-arm unit. Each arm has 7 backdrivable rotary joints and one link-driven parallel gripper. Payload is rated at 4.1 kg nominal and 6.0 kg peak, both including the end effector. The system supports one-way following and bidirectional force feedback, and is intended for teleoperation, demonstration data collection and contact-rich manipulation tasks in research, teaching and development.
Key Features
- 7-DOF humanoid robot arm: 7 backdrivable rotary joints + 1 link-driven parallel gripper per arm, human-scale structure, suitable for desktop and laboratory environments.
- High backdrivability and bidirectional force feedback: compliant QDD joints, support for leader-follower one-way following and bidirectional force feedback; the operator can perceive the follower arm’s contact forces with the environment through the leader arm.
- Link-driven parallel gripper: approx. 88 mm maximum opening, zero position closed, 60° full stroke, suitable for common grasping and contact-rich tasks.
- Real-time status feedback: joint position, velocity, torque, temperature and fault status; zero-position calibration via mechanical limits.
- Optional chest camera: Intel RealSense D435 / D435i, mounted at the chest position for torso view or near-field observation.
- Optional wrist camera: Intel RealSense D405, mounted at the wrist, close-range depth and RGB at 7–50 cm.
- DAMIAO motor platform: 43 series and 8009P series, CAN-FD communication, ROS 2 / MoveIt 2 and SocketCAN support.
- Open end-effector interface: swap grippers, cameras or other tools for custom end-effector development.
Technical Specifications
| System type | OpenArm 1.0 Follower, dual-arm / 2 arms |
|---|---|
| Degrees of freedom | 7 joints + 1 gripper per arm |
| Nominal payload | 4.1 kg, including end effector |
| Peak payload | 6.0 kg, including end effector |
| Design scale | Human-scale, approx. 160–165 cm body height |
| Joint type | QDD backdrivable joints, mechanical limits on every axis |
| Motor platform | DAMIAO 43 series and 8009P series |
| Communication | CAN-FD via USB-to-FDCAN; SocketCAN under Linux |
| End effector | Link-driven parallel gripper, max. opening approx. 88 mm, zero position closed, 60° stroke |
| Optional chest camera | Intel RealSense D435 / D435i; D435i additionally with IMU |
| Optional wrist camera | Intel RealSense D405, 7–50 cm working distance, close-range depth and RGB |
| Software | ROS 2 Humble, MoveIt 2, SocketCAN; RealSense requires separate realsense2_camera driver configuration |
Package Contents
The system is assembled, electrically checked and visually inspected for wiring before delivery.
- 1× OpenArm 1.0 Follower dual-arm system, including housing and internal wiring
- 2× link-driven parallel grippers (left / right), max. opening approx. 88 mm
- 16× DAMIAO motors, per 1.0 platform configuration
- 2× hub / distribution boards
- 1× complete cable set: motor power cables, CAN communication cables, connection and extension cables
- 1× 2-channel USB-to-FDCAN module
- 1× 2000 W power supply with two independent outputs and PFC
- Stable base plate, M6 threaded mounting points
- Assembly and basic functional testing: mechanical inspection, basic electrical inspection, visual wiring inspection
Camera delivery note: Standard delivery does not include cameras. The D435/D435i chest camera and the D405 wrist camera are optional add-ons.
Optional Camera Configurations
Chest camera: Intel RealSense D435 or D435i
Mounted at the chest position for torso view or near-field observation. D435 and D435i share the same mounting; D435i adds an IMU and is suitable for data-collection pipelines requiring inertial data. The 1.0 modular camera mount includes the corresponding D435 chest mounting position.
Wrist camera: Intel RealSense D405
Mounted at the wrist for close-range depth and RGB at 7–50 cm, suitable for precision grasping, hand-eye coordination and contact-state inspection. The D405 is compact (42×42×23 mm, 60 g), USB-C powered, and mounts on the 1.0 wrist mount together with the link-driven parallel gripper. The D405 requires separate realsense2_camera ROS 2 driver configuration.
Application Areas
- Teleoperation: the follower physically executes the movements of a leader system; one-way following and bidirectional force feedback.
- Demonstration data collection: joint and optional visual data (chest / wrist) for imitation learning, Learning from Demonstration and Physical AI.
- Grasping and manipulation: pick-and-place, contact-rich interaction, object transport and experimental manipulation tasks.
- Contact-rich manipulation research: backdrivable joints and force feedback for assembly, insertion and surface tracking.
- Research and prototyping: integration of custom tools, fingers, sensors or end effectors via the open end-effector interface.
Cameras and Software
Standard 1.0 delivery does not include cameras. The D435/D435i chest camera and the D405 wrist camera are optional add-ons and require separate realsense2_camera ROS 2 driver configuration. When using multiple USB 3.0 cameras simultaneously, a USB 3.0 hub with independent power supply is recommended to avoid bandwidth or power limitations and frame drops. Recommended software environment: Ubuntu 22.04 + ROS 2 Humble, motor communication via SocketCAN, MoveIt 2 for dual-arm motion planning.
Compatibility Notice
This product is a compatible implementation based on the OpenArm open-source design, manufactured, assembled and inspected by our team. It is not an official product of the OpenArm project. The 1.0 gripper is a link-driven parallel gripper without an integrated camera; the D405 is mounted externally at the wrist and does not replace the gripper structure. Please contact us for other configurations.
Usage note: Securely mount the robot arm and read the supplied safety instructions; keep the work area clear of people and objects during operation.
Eckstein Robot