USB AVRISP PL AVR ISP Programmer Compatible with ATMEL AT AVRISP

Item number: WS9214D

SKU: USB AVRISP PL

B-A44

Category: Programmer


26,17 €

including 19% VAT.,

Available now!

Shipping time: 1 - 3 workdays



Description

Supports AVR Studio 4 ONLY. Doesn't support AVR Studio 5/6 or higher versions.
  • AVR ISP Programmer, compatible with AT AVRISP from ATMEL
  • A professional low cost In-System Programmer. Programs FLASH , EEPROM, Fuses, and Lock Bit through USB

Features

  • Programs all AVR Devices with ISP programming option, and certain 51 Devices
  • Programs both Flash and EEPROM
  • Supports Fuses and Lock Bit Programming
  • Based on STK500 firmware
  • upgradable to Support Future Devices
  • Adjustable Speed. Supports high speed programming up to 926K frequency
  • Quasi-USB interface to PC for Programming and Control (using PL2303TA, USB To RS232)
  • 3 optional cables to target board
  • Powered from USB bus. No need for Additional Power Supply

Based on AT AVRISP
- Compatible with AT AVRISP, easy to use, stable and reliable

Based on STK500 firmware
- Identified as AVRISP/STK500 in AVRStudio, high speed programming

AVR Studio 4 firmware
- Supports AVR Studio 4
- NOT upgradable

Supported software
- AVR Studio or WINAVR(GCC) is used as front-end software
- Supports the program files generated by IAR, ICCAVR, CVAVR

Device Support
- USB AVRISP supports all AVR 8-bit RISC Micro Controllers with ISP programming option. Support for new devices will be added through new versions of AVR Studio.
- Supports AT86RF401/AT89S51/AT89S52

Refer to AVRStudio 4.18, the following devices are supported:


*Supports all low voltage versions of the devices with suffix of L/V, such as ATmega16L, ATmega48V

Performance
- High speed programs FLASH , EEPROM, Fuses, and Lock Bit
- It takes only 5.5S to program a 12K program file with verification (AVRISP should be set to high speed 926K mode while the default frequency is 230K)

Connects to PC
- Uses a quasi-USB interface for communication with the front-end software (Probably AVR Studio)
- Using PL2303TA, the USB To RS232 chip
- The COM port is configurable, a PC could connects to several USB AVRISP at the same time

Connects to target board
The USB AVRISP connects to the target board through 3 optional cables. Depending on the existed connector on the target board, the cable has to be changed accordingly.
- Standard 10-pin ISP Connector, Using 10-pin ISP cable
- Standard 6-pin ISP Connector, Using 10-pin to 6-pin ISP cable
- Custom ISP Connector, Using 10-wire multicolour custom connector cable
The figure 1 and 2 shows the pinouts for the 10-pin and 6-pin ISP connectors.

  Figure 1. 10-pin ISP Connector
pinouts for 10-pin ISP Connector
Figure 2. 6-pin ISP Connector
pinouts for 6-pin ISP Connector

Powered from USB bus
- Draws power from the USB bus, No need for Additional Power Supply
- The target board should be powered from Another Power Supply

Downloads

Development resources:user guide, software, etc.
Wiki: www.waveshare.com/wiki/USB_AVRISP_PL


Package content

Weight: 0.153 kg

  1. USB AVRISP PL x 1
  2. USB Cable x 1
  3. 10-pin to 6-pin ISP cable x 1
  4. 10-wire multicolour custom connector cable x 1
  5. User Guide CD x 1

Ratings (0)

Average product review

Write your first review and help others with their purchase decision:

Question on item

Question on item