Waveshare Port407Z Development Board Cortex-M4 Entwicklungskit STM32F407

Item number: WS01210

SKU: Port407Z


Category: STM32

33,31 €

including 19% VAT.,

Available now!

Shipping time: 1 - 3 workdays



STM32 development board, features the STM32F407ZET6 MCU, full IO expander, JTAG/SWD debug interface

STM32F407ZET6 development boardOverview

Port407Z is an STM32 development board that features an STM32F407ZET6 device as the microcontroller, supports further expansion with various optional accessory boards for your specific application. It is ideal for starting application development with STM32F family.

Note: Optional accessory boards are NOT included in the price.

What's On Board

STM32F407ZET6 development board on board resource
  1. STM32F407ZET6: the high performance STM32 MCU which features:
    • Core: ARM Cortex-M4 32-bit RISC
    • Feature: a full set of single-cycle DSP instructions
    • Operating frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
    • Operating voltage: 1.8V-3.6V
    • Package: LQFP144
    • Memories: 512KB Flash, 196kB SRAM
    • MCU communication interfaces:
      • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
      • 1 x FSMC, 1 x SDIO, 2 x CAN
      • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
      • 1 x 10/100 Ethernet MAC
      • 1 x 8 to 14-bit parallel camera interface
    • AD & DA converters: 3 x AD (12-bit, 1µs, shares 24 channels); 2 x DA (12-bit)
    • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
  2. AMS1117-3.3: 3.3V voltage regulator
  3. MIC2075-2BM: onboard chip for USB power management
  4. Power indicator
  6. LEDs: convenient for indicating I/O status and/or program running state
  7. Reset button
  8. User keys
  9. Joystick: five positions
  10. 8M crystal oscillator: enables the MCU run at 168M frequency by frequency multiplication
  11. 32.768K crystal (bottom side), for internal RTC with calibration
  12. JTAG/SWD interface: for debugging/programming
  13. USB connector, used for establishing USB communication between PC and the STM32 development board
  14. UART1 connector, supports ISP (In-System Programming) through UART1, as well as system signal output
  15. IO expander, all the MCU pins are accessible on expansion connectors for further expansion
  16. 5V/3.3 V power input/output: usually used as power output, also common-grounding with other user board
  17. 5V DC jack
  18. Boot mode selection: for configuring the BOOT0 and BOOT1 pins
  19. Power supply switch, powered from 5V DC jack or USB connection
  20. USB HOST jumper
    • short the jumper when using USB HOST
    • open the jumper to disconnect from I/O port
  21. VBAT selection jumper
    • short the jumper to use system power supply
    • open the jumper to connect the VBAT to external power, such as battery
  22. VREF jumper
    • short the jumper to connect VREF+/VREF- respectively to VCC/GND
    • open the jumper to connect VREF+/VREF- to other custom pins via jumper wires
  23. User LEDs jumper
    • short the jumper to connect to I/Os used in example code
    • open the jumper to connect to other custom pins via jumper wires
  24. User keys jumper
    • short the jumper to connect to I/Os used in example code
    • open the jumper to connect to other custom pins via jumper wires
  25. Joystick jumper
    • short the jumper to connect to I/Os used in example code
    • open the jumper to connect to other custom pins via jumper wires

Accessory board and programmer/debugger in the photos are NOT included in the price.
Port407Z supports programming through UART port, and requires a debugger for debugging.

JTAG/SWD Interfaces

The figure 1, figure 2 shows the header pinout of JTAG, SWD interface respectively

Figure 1. JTAG Header Pinout
JTAG Header Pinout
Figure 2. SWD Header Pinout
SWD Header Pinout

Development Resources

Port407Z development board comes with a User Guide CD including development resources listed as below:

  • Related software (KEIL etc.)
  • Examples in C
  • Schematic (PDF)
  • Development documentations


STM32 MCU core board dimensions

Package Contains

  1. Port407Z development board x 1
  2. USB power cable x 1
  3. USB type A to Mini-B cable x 1
  4. 4-pin 2-pin wires pack x 1
  5. User guide CD x 1

Ratings (0)

Average product review

Write your first review and help others with their purchase decision:

Question on item

Question on item