Waveshare 0.96 inch 128x64 OLED SPI I2C Interfaces vertical pinheader SSD1306

Item number: WS41006

Note: the 0.96inch OLED consists of 1/4 yellow upper section and 3/4 blue lower section, not a regular dual-color display.

Category: Embed Display


7,15 €

including 19% VAT.,

Please note the long delivery time!

Shipping time: 31 - 33 workdays



Description

Details

0.96inch OLED, SPI/I2C interfaces, straight/vertical pinheader

Key Parameters

Driver Chip SSD1306
Interface 3-wire SPI, 4-wire SPI, I2C
Resolution 128*64
Display Size 0.96inch
Colors 1/4 yellow section, 3/4 blue section
Visible Angle >160°
Operating Temp. (?) -20~70
Storage Temp. (?) -30~80
Operating Voltage 3.3V / 5V

Interface

PIN NO. SYMBOL DESCRIPTION
1 VCC Power positive (3.3~5V power input)
2 GND Ground
3 NC NC
4 DIN Data input
5 CLK Clock signal input
6 CS Chip selection, low active
7 D/C Command signal, low level for command, high level for data
8 RES Reset signal, low active

Hardware Config

Mode/Interface BS0/BS1 DIN SCK
3-wire SPI 1/0 MOSI SCLK
4-wire SPI 0/0
I2C 0/1 SDA SCL

Ordering Info

The 0.96inch OLED provides 2 options for the onboard pinheader:

  • 0.96inch OLED (A): angled/horizontal pinheader
  • 0.96inch OLED (B): straight/vertical pinheader

Selection Guide

Part Number Color Resolution Display Size (mmxmm) Interfaces Driver Dimension (mmxmm) Pinheader
0.95inch RGB OLED (A) 65K colorful 96x64 20.14x13.42 SPI(4-wire SPI) SSD1331 31.7x37.0 angled/horizontal
0.95inch RGB OLED (B) 65K colorful 96x64 20.14x13.42 SPI(4-wire SPI) SSD1331 31.7x37.0 straight/vertical
0.96inch OLED (A) 1/4 yellow section, 3/4 blue section 128x64 21.7x11.2 3-wire SPI, 4-wire SPI, I2C SSD1306 33.0x33.5 angled/horizontal
0.96inch OLED (B) 1/4 yellow section, 3/4 blue section 128x64 21.7x11.2 3-wire SPI, 4-wire SPI, I2C SSD1306 33.0x33.5 straight/vertical
1.3inch OLED (A) Blue 128x64 29.42x14.7 3-wire SPI, 4-wire SPI, I2C SH1106 40.5x37.5 angled/horizontal
1.3inch OLED (B) Blue 128x64 29.42x14.7 3-wire SPI, 4-wire SPI, I2C SH1106 40.5x37.5 straight/vertical
1.5inch OLED Module White (16-bit grey level) 128x128 26.86x26.86 4-wire SPI, I2C SSD1327 44.5x37.0 PH2.0 connector

Note: the 0.96inch OLED consists of 1/4 yellow upper section and 3/4 blue lower section, not a regular dual-color display.

Package Content

0.96inch OLED (B) x 1

Documents

Wiki

Ratings (4)

Average product review

4 Stars
3 Stars
2 Stars
1 Star

Share your experience with other customers:

Total entries: 1
5 from 5 Works perfectly controlled by an ATMEGA328P

As shown in this screenshot...

https://www.thanassis.space/IMG_20161119_182304.jpg

...the screen works fine over the SPI pins of an ATMEGA328P.
Connections:

DIN => Pin 17 (Arduino pin 11, MOSI/PWM, B3)
CLK => Pin 19 (Arduino pin 13, SCK, B5)
CS => Pin 16 (Arduino pin 10, PWM, B2)
D/C => Pin 15 (Arduino pin 9, B1)
Reset => Pin 14 (Arduino pin 8, B0)

Also of note - as shown in the picture, the SPI pins (19,18,17) can be used at the same time to program the ATMEGA328P from a Raspberry PI. There is no conflict there, since the pins are used as input during programming and become output (controlling the SSD1306) afterwards.

Very pleased with the result - nice screen.

., 19.11.2016
Total entries: 1

Other customers have also bought the following items
Jumper Wire 10x1P female to male 20cm Jumper Wire 10x1P female to male 20cm
Available now!
Jumper Wire 10x1P female to female 20cm
Available now!
HIMALAYA basic MEGA 2560 R3 ATMEGA Board Arduino Mega... HIMALAYA basic MEGA 2560 R3 ATMEGA Board Arduino Mega...
Available now!
Jumper Wire 10x1P male to male 20cm
Available now!
NodeMcu Lua WIFI Internet Development Board based on... NodeMcu Lua WIFI Internet Development Board based on...
Available now!
HIMALAYA basic UNO R3 ATmega328P Board ATmega16U2 mit USB... HIMALAYA basic UNO R3 ATmega328P Board ATmega16U2 mit USB...
Available now!