Pololu Tic T825 USB Multi-Interface Stepper Motor Controller 3131

Pololu

Pololu Tic T825 USB Multi-Interface Stepper Motor Controller 3131

SKU: PO3131

42,95 €

per pack

incl. 19% VAT plus

Net: 36,09 €

Choose tax zone / country of delivery

Product customisation & sourcing & PCBA one-stop service are available with us.

Request personal offer!

Available immediately

Delivery time: 2 - 3 weeks (DE - int. shipments may differ)

Product Information

Product safety information

Manufacturer information:

Pololu Corporation
Pilot Rd. 920
Nevada
Las Vegas, Vereinigte Staaten, 89119
[email protected]
https://www.pololu.com/

Responsible person:

Eckstein GmbH
Am Ostbahnhof 3
Niedersachsen
Clausthal-Zellerfeld, Deutschland, 38678
[email protected]
https://eckstein-shop.de

Dimensions and Weight
GTIN:	4060137033353
HAN:	3131
Category:	Tic Stepper Motor Controllers
Shipping weight:	0,01 kg
Item weight:	0,01 kg
Dimensions ( Length × Width × Height ):	3,80 × 2,60 × 1,30 cm

Product Description

Overview

The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates a TI DRV8825 driver, and male headers and terminal blocks are included but not soldered. It can operate from 8.5 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2.5 A max with sufficient additional cooling).

Features and specifications

Open-loop speed or position control of one bipolar stepper motor
A variety of control interfaces:
- USB for direct connection to a computer
- TTL serial operating at 5 V for use with a microcontroller
- I²C for use with a microcontroller
- RC hobby servo pulses for use in an RC system
- Analog voltage for use with a potentiometer or analog joystick
- Quadrature encoder input for use with a rotary encoder dial, allowing full rotation without limits (not for position feedback)
- STEP/DIR inputs for compatibility with existing stepper motor control firmware
Acceleration and deceleration limiting
Maximum stepper speed: 50,000 steps per second
Very slow speeds down to 1 step every 200 seconds (or 1 step every 1428 seconds with reduced resolution).
Selectable microstep modes up to 1/256-step resolution:
- The Tic 36v4 supports full-step to 1/256-step modes
- The Tic T825, Tic T834, and T249 support full-step to 1/32-step modes
- The Tic T500 supports full-step to 1/8-step modes
Digitally adjustable current limit
Optional safety controls to avoid unexpectedly powering the motor
Input calibration (learning) and adjustable scaling degree for analog and RC signals
5 V regulator (no external logic voltage supply needed)
Optional limit switch inputs with homing capabilities
Optional kill switch inputs
STEP/DIR outputs for controlling external stepper motor drivers
Connects to a computer through USB via a USB A to Micro-B cable (not included)
Free configuration software available for Windows, Linux, and macOS
Arduino library makes it easy to get started using these controllers with an Arduino or compatible board
Comprehensive user’s guide

Dimensions

Size:1.50? × 1.05? × 0.42?¹
Weight:5.1 g¹

General specifications

Model:Tic T825
Motor driver:DRV8825
Control interface:
- USB; non-inverted TTL serial; I²C;
- RC servo pulses; analog voltage; quadrature encoder
Minimum operating voltage:8.5 V
Maximum operating voltage:45 V²
Continuous current per phase:1.5 A³
Maximum current per phase:2.5 A⁴
Maximum step rate:50000 PPS
Microstep resolutions:full, 1/2, 1/4, 1/8, 1/16, and 1/32
Reverse voltage protection?:Y⁵
Connectors soldered?:N

Identifying markings

PCB dev codes:tic01a
Other PCB markings:0J10475

Notes:

1.Without included optional hardware.
2.Reverse voltage protection only works up to 40 V.
3.Without a heat sink or forced air flow.
4.With sufficient additional cooling.
5.To -40 V. Connecting supplies over 40 V in reverse can damage the device.

Write the first review for this item and help others make a purchase decision!

User's Guide

Manufacturer according to GPSR
Pololu Corporation, Pilot Rd. 920, 89119 Las Vegas, Nevada, Vereinigte Staaten, [email protected], https://www.pololu.com/
Responsible person according to GPSR
Eckstein GmbH, Am Ostbahnhof 3, 38678 Clausthal-Zellerfeld, Niedersachsen, Deutschland, [email protected], https://eckstein-shop.de