Pololu PIR Motion Sensor

Artikelnummer: PO2731


  Der PIR erfasst Lichtquellen mit einer Wellenlänge von 700nm bis 1400nm. Da der Mensch Wellenlängen von 800nm bis 1400nm emittiert ist er also perfekt zum erfassen von menschlichen Bewegungen.

Kategorie: Infrarot Zähler/ Bewegungsmelder


9,95 €

inkl. 19% USt.,

4 Packung auf Lager

Lieferfrist: ca. 1 - 2 Tage

Packung


Beschreibung

Overview

The passive infrared detector senses motion of infrared light sources at the same wavelengths humans emit. Passive infrared detectors like this one are used in security and automation applications. In security, motion sensors are integrated into alarm systems and used to turn on security cameras. PIR motion sensors are also used to automatically turn on lights when people enter a room.

The two pyroelectric sensing elements allow the PIR motion sensor to see moving infrared light sources while ignoring changes in background infrared radiation. A lens focuses the infrared light on to the two silicon-coated sensing elements.

When the sensor is powered on, it takes 1 to 2 seconds to calibrate itself to the background infrared radiation before it can detect motion. After calibration, the detector drives the open-collector Alarm pin low for the duration of the sensed motion (the alarm pin state is not latched); when there is no motion detected, the alarm pin is floating. The open-collector setup allows multiple motion sensors to be connected on a single input pin, but it means that you will need an external pull-up resistor on the alarm pin. If any of the motion sensors go off, the input pin will be pulled low.

We expect this PIR motion sensor to be functionally the same as our older version; the only thing that changed is the connector, which is now a 3-pin female JST PH-style connector. This connector has a 2 mm pitch and is not compatible with 0.1?-spaced connectors. For use with common 0.1?-spaced connectors or breadboards, you might consider cutting off the JST connector and splicing on a connector of your choice.

Connections

Note: The cable wire colors can vary. Referring to the top-view picture above, the left-most wire is power, the middle wire is the ground, and the right-most wire is alarm.

This sensor should be powered at 12 V; our U3V12VF12 12V boost regulator and S10V2F12 12V step-up/step-down regulator are good options for powering this sensor from input voltages other than 12 V. The signal is an open-collector output, which requires an external pull-up resistor.

Note: SparkFun calls this product the ?PIR Motion Sensor (JST)? SKU: SEN-13285. It replaces the older Passive Infrared (PIR) Detector SE-10.

Dokumente

Bedienungsanleitung

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

----

Diese Modul passt zu folgende Produkten:
0.1 (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack 0.1 (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack
50 Packung auf Lager
Female Crimp Pins for 0.1 Housings 100-Pack Female Crimp Pins for 0.1 Housings 100-Pack
26 Packung auf Lager
Pololu 12V Step-Up Spannungsregler U3V12F12 Pololu 12V Step-Up Spannungsregler U3V12F12
1 Packung auf Lager
Pololu 12V Step-Up Step-Down Spannungsregler S10V2F12 Pololu 12V Step-Up Step-Down Spannungsregler S10V2F12
5 Packung auf Lager
Kunden kauften dazu folgende Produkte
Jumper Wire 10x1P male to male 20cm
6 Packung auf Lager
DS3231 RTC Modul LIR2032 DS3231 RTC Modul LIR2032

DS3231 RTC Modul LIR2032


2,75 € *
Alter Preis: 3,86 €
23 Packung auf Lager
Jumper Wire 10x1P female to male 20cm Jumper Wire 10x1P female to male 20cm
232 Packung auf Lager
Adafruit NeoPixel Ring - 12 x 5050 RGB LED with... Adafruit NeoPixel Ring - 12 x 5050 RGB LED with...
2 Packung auf Lager
ISD1820 Voice Recording and Playback Module with Mic Sound ISD1820 Voice Recording and Playback Module with Mic Sound
15 Packung auf Lager