Pololu MinIMU-9 v5 Gyro, Accelerometer, and Compass (LSM6DS33 and LIS3MDL Carrier)

Artikelnummer: PO2738

EAN: 4060137017452

Hersteller-Artikelnr.: 2738

The Pololu MinIMU-9 v5 is an inertial measurement unit (IMU) that packs an LSM6DS33 3-axis gyro and 3-axis accelerometer and an LIS3MDL 3-axis magnetometer onto a tiny 0.8? × 0.5? board. An I²C interface accesses nine independent rotation, acceleration, and magnetic measurements that can be used to calculate the sensor?s absolute orientation. The MinIMU-9 v5 board includes a voltage regulator and a level-shifting circuit that allow operation from 2.5 to 5.5 V, and the 0.1? pin spacing makes it easy to use with standard solderless breadboards and 0.1? perfboards.

Kategorie: Beschleunigung /Gyroskop /Kompass


14,23 €

inkl. 19% USt.,

5 bestellt, am 23.08.2017 erwartet

Lieferzeit: 5 bis 6 Tage

Stück


Beschreibung

Overview

The Pololu MinIMU-9 v5 is a compact (0.8″ × 0.5″) board that combines ST’s LSM6DS33 3-axis gyroscope and 3-axis accelerometer and LIS3MDL 3-axis magnetometer to form an inertial measurement unit (IMU); we therefore recommend careful reading of the LSM6DS33 datasheet (1MB pdf) and LIS3MDL datasheet (2MB pdf) before using this product. These sensors are great ICs, but their small packages make them difficult for the typical student or hobbyist to use. They also operate at voltages below 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. The MinIMU-9 v5 addresses these issues by incorporating additional electronics, including a voltage regulator and a level-shifting circuit, while keeping the overall size as compact as possible. The board ships fully populated with its SMD components, including the LSM6DS33 and LIS3MDL, as shown in the product picture.

Compared to the previous MinIMU-9 v3, the v5 version uses newer MEMS sensors that provide some increases in accuracy (lower noise and zero-rate offsets). The MinIMU-9 v5 is pin-compatible with the MinIMU-9 v3, but because it uses different sensor chips, software written for older IMU versions will need to be changed to work with the v5.

The MinIMU-9 v5 is also pin-compatible with the AltIMU-10 v5, which offers the same functionality augmented by a digital barometer that can be used to obtain pressure and altitude measurements. The AltIMU includes a second mounting hole and is 0.2″ longer than the MinIMU. Any code written for the MinIMU-9 v5 should also work with the AltIMU-10 v5.

The LSM6DS33 and LIS3MDL have many configurable options, including dynamically selectable sensitivities for the gyro, accelerometer, and magnetometer. Each sensor also has a choice of output data rates. The two ICs can be accessed through a shared I²C/TWI interface, allowing the sensors to be addressed individually via a single clock line and a single data line. Additionally, a slave address configuration pin allows users to change the sensors’ I²C addresses and have two MinIMUs connected on the same I²C bus. (For additional information, see the I²C Communication section below.)

The nine independent rotation, acceleration, and magnetic readings (sometimes called 9DOF) provide all the data needed to make an attitude and heading reference system (AHRS). With an appropriate algorithm, a microcontroller or computer can use the data to calculate the orientation of the MinIMU board. The gyro can be used to very accurately track rotation on a short timescale, while the accelerometer and compass can help compensate for gyro drift over time by providing an absolute frame of reference. The respective axes of the two chips are aligned on the board to facilitate these sensor fusion calculations. (For an example of such a system using an Arduino, see the picture below and the Sample Code section at the bottom of this page.)

The carrier board includes a low-dropout linear voltage regulator that provides the 3.3 V required by the LSM6DS33 and LIS3MDL, allowing the module to be powered from a single 2.5 V to 5.5 V supply. The regulator output is available on the VDD pin and can supply almost 150 mA to external devices. The breakout board also includes a circuit that shifts the I²C clock and data lines to the same logic voltage level as the supplied VIN, making it simple to interface the board with 5 V systems. The board’s 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards.

Specifications

  • Dimensions: 0.8″ × 0.5″ × 0.1″ (20 mm × 13 mm × 3 mm)
  • Weight without header pins: 0.7 g (0.02 oz)
  • Operating voltage: 2.5 V to 5.5 V
  • Supply current: 5 mA
  • Output format (I²C):
    • Gyro: one 16-bit reading per axis
    • Accelerometer: one 16-bit reading per axis
    • Magnetometer: one 16-bit reading per axis
  • Sensitivity range:
    • Gyro: ±125, ±245, ±500, ±1000, or ±2000°/s
    • Accelerometer: ±2, ±4, ±8, or ±16 g
    • Magnetometer: ±4, ±8, ±12, or ±16 gauss

Document

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

Frage zum Produkt

Kontaktdaten
Frage zum Produkt
max. 500 Zeichen

ähnliche Produkte:
Pololu AltIMU-10 v5 Gyro, Accelerometer, Compass, and... Pololu AltIMU-10 v5 Gyro, Accelerometer, Compass, and...
Lange Lieferzeit beachten!
Pololu L3GD20H 3-Axis Gyro Carrier with Voltage Regulator Pololu L3GD20H 3-Axis Gyro Carrier with Voltage Regulator
sofort verfügbar
Pololu LIS3MDL 3-Axis Magnetometer Carrier with Voltage... Pololu LIS3MDL 3-Axis Magnetometer Carrier with Voltage...
sofort verfügbar
Pololu LPS25H Pressure Altitude Sensor Carrier with... Pololu LPS25H Pressure Altitude Sensor Carrier with...
sofort verfügbar
Pololu LSM303D 3D Compass and Accelerometer Carrier with... Pololu LSM303D 3D Compass and Accelerometer Carrier with...
Lange Lieferzeit beachten!
Pololu LSM6DS33 3D Accelerometer and Gyro Carrier with... Pololu LSM6DS33 3D Accelerometer and Gyro Carrier with...
sofort verfügbar
Kunden kauften dazu folgende Produkte
Pololu LSM6DS33 3D Accelerometer and Gyro Carrier with... Pololu LSM6DS33 3D Accelerometer and Gyro Carrier with...
sofort verfügbar
HC-SR04 Abstandsmessung Ultraschall Ultrasonic Sensor Module
sofort verfügbar
5 Stücke 2Pin 20cm Jumper Cable Wire Female to Female
sofort verfügbar
Adafruit Feather M0 Adalogger Adafruit Feather M0 Adalogger
sofort verfügbar
Pololu 5V, 2.5A Step-Down Spannungsregler D24V25F5 Pololu 5V, 2.5A Step-Down Spannungsregler D24V25F5
sofort verfügbar