Pololu MAX14870 Single Brushed DC Motortreiber Carrier

Item number: PO2961

This compact breakout board for Maxim's MAX14870 motor driver offers a wide operating voltage range of 4.5V to 36V and can deliver a continuous 1.7A (2.5A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.

Category: DC Motor Driver


6,66 €

including 19% VAT.,

Available now!

Shipping time: 1 - 2 workdays



Description

Overview

The MAX14870 from Maxim Integrated is a tiny H-bridge motor driver IC that can be used for bidirectional control of one brushed DC motor at 4.5 V to 36 V. It can supply up to about 1.7 A continuously and can tolerate peak currents up to 2.5 A for a few seconds, making it a good choice for small motors that run on a wide range of voltages. The MAX14870 is a great IC, but its small surface-mount package makes it difficult for the typical student or hobbyist to use; our breakout board makes it easy to use with standard solderless breadboards and 0.1? perfboards. Since this board is a carrier for the MAX14870, we recommend careful reading of the MAX14870 datasheet (492k pdf). The board ships populated with SMD components, including the MAX14870 and a reverse battery protection circuit.

For similar motor drivers that operate at lower voltages, consider our BD65496MUV and DRV8838 motor driver carriers.

Features

  • Single-channel H-bridge motor driver with shoot-through protection and internal free-wheeling diodes (can drive one DC motor)
  • Motor supply voltage: 4.5 V to 36 V
  • Output current: up to 1.7 A continuous (2.5 A peak)
  • No separate logic supply needed; inputs are 3V- and 5V-compatible
  • simple two-pin DIR/PWM interface (one pin controls direction and another controls speed)
  • Under-voltage lockout on the logic supply and protection against over-current/short-circuit and over-temperature
  • Carrier board adds reverse-voltage protection
  • Active-low fault output indicates over-current or over-temperature condition
  • Surface-mount resistor can optionally be added to enable automatic current limiting
  • Compact size (0.6?×0.5?)

Included hardware

Two 1×5-pin breakaway 0.1? male headers are included with the MAX14870 motor driver carrier, which can be soldered in to use the driver with breadboards, perfboards, or 0.1? female connectors. (The headers might ship as a single 1×10 piece that can be broken in half.) The right picture above shows the two possible board orientations when used with these header pins (parts visible or silkscreen visible). You can also solder your motor leads and other connections directly to the board.

Ratings (1)

Average product review

Share your experience with other customers:


Other customers have also bought the following items
DRV8801 Single Brushed DC Motor Driver Carrier DRV8801 Single Brushed DC Motor Driver Carrier
Please note the long delivery time!
Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
Available now!
Pololu DRV8838 Single Brushed DC Motor Driver Carrier Pololu DRV8838 Single Brushed DC Motor Driver Carrier
25 ordered, expected on 10.03.2021
Jumper Wire 10x1P female to male 20cm Jumper Wire 10x1P female to male 20cm
Available now!
DS3231 RTC Modul LIR2032 DS3231 RTC Modul LIR2032
Available now!
Pololu Universal Aluminum Mounting Hub for 6mm Shaft, M3... Pololu Universal Aluminum Mounting Hub for 6mm Shaft, M3...
24 ordered, expected on 10.03.2021