Pololu High-Power Stepper Motor Driver 36v4

Item number: PO3730

Category: Driver


18,81 €

including 19% VAT.,

Available now!

Shipping time: 1 - 3 workdays



Description

New revision: As of 19 September 2019, we are shipping a slight revision (md38b) with improved noise and fault tolerance at high input voltages and high current limits.

Overview

The Pololu High-Power Stepper Motor Driver 36v4 combines the DRV8711 stepper motor driver IC from Texas Instruments with external MOSFETs to enable control of large bipolar stepper motors at operating voltages from 8 V to 50 V. The DRV8711 has many configurable settings, so please see the DRV8711 datasheet (3MB pdf) for a detailed explanation of its features and how to use them (we also have an Arduino library that simplifies getting started by providing basic functions for configuring and operating the driver).

The driver?s power performance is a function of the external dual H-bridges, which allow the driver to deliver continuous currents up to 4 A per phase without any additional cooling such as heat sinks or forced air flow. (With sufficient additional cooling, the driver can support currents up to around 6 A per phase; see the Power dissipation considerations section below for more information, including important information about using this product safely.)

Key features

  • Wide 8 V to 50 V operating voltage range
  • High-power: can deliver up to 4 A continuous per phase without extra cooling (6 A max with sufficient additional cooling)
  • Highly configurable through SPI interface
  • Optional STEP/DIR control pins (stepping can also be controlled through SPI interface alone)
  • Nine different step resolutions down to 256 microsteps: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, 1/32-step, 1/64-step, 1/128-step, and 1/256-step
  • Adjustable current control lets you set the maximum current output, enabling the use of voltages above your stepper motor?s rated voltage to achieve higher step rates
  • Adaptive blanking time, adjustable decay times, and various current decay modes enable the creation of ultra-smooth motion profiles through the SPI interface
  • Optional STALL output enables stall detection when microstepping
  • Optional BEMF output enables more advanced control and stall detection algorithms based on the back EMF of the stepper motor
  • Driver supports alternate operating mode for controlling two brushed DC motors with PWM inputs instead of one bipolar stepper motor with STEP/DIR inputs
  • Inputs compatible with 1.8 V, 3.3 V, and 5 V logic
  • Digital outputs are all open drain with pull-ups to externally supplied IOREF voltage for use with non-5V systems (IOREF can be connected to neighboring 5V OUT pin for use with 5V systems)
  • Under-voltage lockout, over-current protection, short circuit protection, and reverse-voltage protection (up to 40 V)
  • Arduino library and example sketches are available that provide basic functions for configuring and operating the driver

As an alternative to this stepper motor driver, our Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller has similar power characteristics and offers high-level interfaces (USB, TTL serial, I²C, analog voltage, quadrature encoder, and RC hobby servo pulses) that make it easier to use for some applications. The Tic?s configuration software allows you to change many of the driver?s settings over USB, eliminating the need to directly use SPI to configure the DRV8711.

Dimensions

  • Size:1.3? × 1.2?
  • Weight:4.9 g1

General specifications

  • Minimum operating voltage:8 V
  • Maximum operating voltage:50 V
  • Continuous current per phase:4 A2
  • Maximum current per phase:6 A3
  • Minimum logic voltage:1.5 V
  • Maximum logic voltage:5.5 V
  • Microstep resolutions:full, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256
  • Current limit control:SPI-programmable
  • Reverse voltage protection?:Y4
  • Header pins soldered?:N

Identifying markings

  • PCB dev codes:md38a, md38b
  • Other PCB markings:0J12286, 0J12459

Notes:

1.Without included optional headers or terminal blocks.
2.Without a heat sink or forced air flow.
3.With sufficient additional cooling. This limitation comes from the 30 m? current sense resistors, which are rated for 1 W.
4.To -40 V. Connecting supplies over 40 V in reverse can damage the device.

Ratings (0)

Average product review

Write your first review and help others with their purchase decision:


Other customers have also bought the following items
HIMALAYA basic MEGA 2560 R3 ATMEGA Board Arduino Mega... HIMALAYA basic MEGA 2560 R3 ATMEGA Board Arduino Mega...
Available now!
SparkFun RJ45 Breakout Board for Ethernet Jacks SparkFun RJ45 Breakout Board for Ethernet Jacks
Available now!
Pololu Stamped Aluminum L-Bracket for NEMA 17 Stepper Motors Pololu Stamped Aluminum L-Bracket for NEMA 17 Stepper Motors
Available now!