Pololu Crimping Tool 0.1-1.0 mm² Capacity, 16-28 AWG Werkzeug

Artikelnummer: PO1928

This crimping tool can be used to crimp both male and female versions of our Tamiya connector crimp pins, mini Tamiya connector crimp pins, JST connector crimp pins, JR crimp pins, Futaba J crimp pins, and crimp pins for 0.1" housings onto 16-28 AWG wires to make custom cables. The crimping die has a width of 7 mm, and the tool offers ratcheting action for increased consistency and ease of use.

Kategorie: Werkzeuge


34,95 €

inkl. 19% USt.,

sofort verfügbar

Lieferfrist: ca. 1 - 3 Tage

Stück


Beschreibung

Selecting the Right Tool

We also have a less expensive, narrower (4 mm) crimper that can also crimp JST RCY, JR, Futaba J, and 0.1" housing crimp pins, though this alternate tool can only crimp the full extent of wire barrel on the JST RCY pins. You can use the following table to help you decide which cavity of which crimping tool you need:

Using the Crimping Tool

Prepare the wire by stripping about 1/8" (3 mm) of insulation from the end. Place the wire in the crimp pin, lining it up so that the stripped portion lies between the inner set of tabs on the crimp pin, while insulated wire lies between the outer set of tabs
.



Place the wire and crimp pin on the appropriate tooth of the tool?s die, making sure that the insulated end is on the raised and wider half of the tooth. The tabs should point toward the cavity on the other side of the die so that the tool bends them inward around the wire when it closes.

Close the jaws of the tool slowly and completely until they release. The tabs on a properly crimped pin should form one barrel around the wire conductors and another barrel for strain relief around the wire insulation.



Tip:
 The strain relief barrel sometimes ends up a little overly flattened, making it too wide to fit comfortably into the crimp pin housing. In such situations, you can use a pair of pliers to gently squeeze the wider axis of the barrel into a more cylindrical shape that will slide easily into the housing.

Package List

1x Crimping Tool: 0.1-1.0 mm² Capacity, 16-28 AWG

Dokumente

Video Tutorial

https://www.youtube.com/watch?feature=player_embedded&v=K7Qb3DzIX3s

Video Tutorial

Check Points for Correct Crimping

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

----

Diese Modul passt zu folgende Produkten:
Female Crimp Pins for 0.1 Housings 100-Pack Female Crimp Pins for 0.1 Housings 100-Pack
sofort verfügbar
Male Crimp Pins for 0.1 Housings 100-Pack Male Crimp Pins for 0.1 Housings 100-Pack
sofort verfügbar
ähnliche Produkte:
Kabelschneider 10-18AWG Cable Cutter & Stripper 0,9-5,5mm² Kabelschneider 10-18AWG Cable Cutter & Stripper 0,9-5,5mm²
sofort verfügbar
Kabelschuh Crimpzange  für insulated Terminal SN-02C 0,25... Kabelschuh Crimpzange  für insulated Terminal SN-02C 0,25...
sofort verfügbar
Pololu Crimping Tool 0.08-0.5 mm² Capacity 20-28 AWG... Pololu Crimping Tool 0.08-0.5 mm² Capacity 20-28 AWG...
sofort verfügbar
Wire End Cord Lug ferrule Crimper tool square crimp 0,25... Wire End Cord Lug ferrule Crimper tool square crimp 0,25...
10 bestellt, am 26.10.2018 erwartet
Kunden kauften dazu folgende Produkte
0.1 (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack 0.1 (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack
sofort verfügbar
Female Crimp Pins for 0.1 Housings 100-Pack Female Crimp Pins for 0.1 Housings 100-Pack
sofort verfügbar
Jumper Wire 10x1P female to female 20cm
sofort verfügbar
0.1 (2.54mm) Crimp Connector Housing: 1x4-Pin 10-Pack 0.1 (2.54mm) Crimp Connector Housing: 1x4-Pin 10-Pack
sofort verfügbar
Male Crimp Pins for 0.1 Housings 100-Pack Male Crimp Pins for 0.1 Housings 100-Pack
sofort verfügbar
Jumper Wire 10x1P female to male 20cm Jumper Wire 10x1P female to male 20cm
sofort verfügbar