Pololu Crimping Tool 0.08-0.5 mm² Capacity 20-28 AWG Werkzeug

Artikelnummer: PO1929

This crimping tool can be used to crimp both male and female versions of our JST connector crimp pins, JR crimp pins, Futaba J crimp pins, and crimp pins for 0.1" housings onto 20-28 AWG wires to make custom cables. The crimping die has a width of 4 mm, and the tool offers ratcheting action for increased consistency and ease of use.

Kategorie: Werkzeuge


35,64 €

inkl. 19% USt.,

momentan nicht verfügbar


Beschreibung

Selecting the Right Tool

We also have a more versatile, wider (7 mm) crimper that can additionally crimp Tamiya and mini Tamiya connector crimp pins. Because the more versatile tool is wider, it can crimp the full wire barrel on the 0.1" housing crimp pins rather than just part of the wire barrel. You can use the following table to help you decide which cavity of which crimping tool you need:

Using the Crimping Tool

Prepare the wire by stripping about 1/8" (3 mm) of insulation from the end. Place the wire in the crimp pin, lining it up so that the stripped portion lies between the inner set of tabs on the crimp pin, while insulated wire lies between the outer set of tabs.

Place the wire and crimp pin on the appropriate tooth of the tool?s die, making sure that the insulated end is on the raised and wider half of the tooth. The tabs should point toward the cavity on the other side of the die so that the tool bends them inward around the wire when it closes. The picture below shows our more versatile crimping tool, but the procedure is the same for this crimper.

Close the jaws of the tool slowly and completely until they release. The tabs on a properly crimped pin should form one barrel around the wire conductors and another barrel for strain relief around the wire insulation. When using this narrower crimper on the JR, Futaba J, and 0.1" housing crimp pins, only part of the wire barrel gets crimped, but it is still enough to make a sufficient electrical connection to the wire conductors, and the uncrimped portion of the wire barrel will be concealed by the crimp pin housing. This tool is wide enough to crimp the full wire barrel of the JST RCY crimp pins.

Tip: The strain relief barrel sometimes ends up a little overly flattened, making it too wide to fit comfortably into the crimp pin housing. In such situations, you can use a pair of pliers to gently squeeze the wider axis of the barrel into a more cylindrical shape that will slide easily into the housing.

Package List

1x Pololu Crimping Tool: 0.08-0.5 mm² Capacity, 20-28 AWG

Dokumente

Video Tutorial

https://www.youtube.com/watch?feature=player_embedded&v=K7Qb3DzIX3s

Video Tutorial

Check Points for Correct Crimping

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

----

Diese Modul passt zu folgende Produkten:
Female Crimp Pins for 0.1 Housings 100-Pack Female Crimp Pins for 0.1 Housings 100-Pack
28 Packung auf Lager
Male Crimp Pins for 0.1 Housings 100-Pack Male Crimp Pins for 0.1 Housings 100-Pack
184 Packung auf Lager
ähnliche Produkte:
Kabelschneider 10-18AWG Cable Cutter & Stripper 0,9-5,5mm² Kabelschneider 10-18AWG Cable Cutter & Stripper 0,9-5,5mm²
2 Packung auf Lager
Kabelschuh Crimpzange  für insulated Terminal SN-02C 0,25... Kabelschuh Crimpzange  für insulated Terminal SN-02C 0,25...
4 Packung auf Lager
Pololu Crimping Tool 0.1-1.0 mm² Capacity, 16-28 AWG... Pololu Crimping Tool 0.1-1.0 mm² Capacity, 16-28 AWG...
2 Packung auf Lager
Wire End Cord Lug ferrule Crimping tool 0,25 - 6mm² Wire End Cord Lug ferrule Crimping tool 0,25 - 6mm²
4 Packung auf Lager
Kunden kauften dazu folgende Produkte
Female Crimp Pins for 0.1 Housings 100-Pack Female Crimp Pins for 0.1 Housings 100-Pack
28 Packung auf Lager
Male Crimp Pins for 0.1 Housings 100-Pack Male Crimp Pins for 0.1 Housings 100-Pack
184 Packung auf Lager
0.1 (2.54mm) Crimp Connector Housing: 1x4-Pin 10-Pack 0.1 (2.54mm) Crimp Connector Housing: 1x4-Pin 10-Pack
1338 Packung auf Lager
0.1 (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack 0.1 (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack
291 Packung auf Lager
2,54mm Dupont Jumper Crimp Connector Housing Stecker...
1338 auf Lager
HC-SR04 Abstandsmessung Ultraschall Ultrasonic Sensor Module HC-SR04 Abstandsmessung Ultraschall Ultrasonic Sensor Module
43 Packung auf Lager