Ion Motion Control RoboClaw 2x 60A Motor Controller (V5)

Artikelnummer: PO1499

Hersteller Artikel Nr.: 1499

The RoboClaw motor controllers from Ion Motion Control (formerly Orion Robotics) can control a pair of brushed DC motors using USB serial, TTL serial, RC, or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system. This version can supply a continuous 60 A per channel (120 A peak).

Kategorie: Motoren

237,94 €

inkl. 19% USt.,

sofort verfügbar

Lieferzeit: 1 bis 2 Tage




The RoboClaw from Ion Motion Control (formerly Orion Robotics) is an efficient, versatile, dual-channel synchronous regenerative motor controller. It can supply two brushed DC motors with 7.5 A, 15 A, 30 A, 45 A, or 60 A continuous (depending on the model) at voltages from 6 V to 34 V, and it allows for peak currents up to twice the maximum continuous rating.

The RoboClaw features dual quadrature decoding capability. A built-in PID routine can be used for closed-loop speed control, maintaining motor speeds even if the load varies, or the encoder counts and speeds can be read directly from the RoboClaw for use with an external control system. Analog feedback is also supported for closed-loop position control.

The RoboClaw has a USB interface that acts as a virtual serial (COM) port, allowing it to be controlled directly from a computer. Several other interface modes are supported by the RoboClaw as well: it can be controlled via TTL serial for use with an embedded system, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), or analog voltages for use with potentiometers or analog joysticks.

The RoboClaw 2x7A (V5), 2x15A (V5), 2x30A (V5), 2x45A (V5), and 2x60A (V5) have USB Micro-B connectors; older USB RoboClaws had a USB Mini-B connector.

Details for item #1499

Note: As of April 25, 2016, we are shipping the V5 version of the RoboClaw 2x60A instead of V4. The performance specifications have not changed from V4 to V5, but the USB Mini-B connector has been replaced with a Micro-B connector, and the layout of some of the components is different. The most noticeable physical change is to the heat sink and power capacitors; the pictures below show the older V4 (left) next to the newer V5 (right):

Ion Motion Control RoboClaw 2×60A dual motor controller with USB (V4).

Ion Motion Control RoboClaw 2×60A dual motor controller with USB (V5).

Key Features

  • Simple bidirectional control of two brushed DC motors
  • 6 V to 34 V operating supply range
  • 7.5 A to 60 A maximum continuous current output, depending on controller model
  • Automatic current limiting reduces duty cycle when motor current is between 1× and 2× the controller?s rated current
  • Four communication or control options:
    1. USB serial interface (virtual COM port)
    2. Logic-level (TTL) serial interface for direct connection to microcontrollers or other embedded controllers
    3. Hobby radio control (RC) pulse width interface for direct connection to an RC receiver or RC servo controller
    4. 0 V to 2 V (5 V tolerant) analog voltage interface for direct connection to potentiometers and analog joysticks
  • Dual feedback inputs for PID closed-loop control:
    • Speed control with quadrature encoders, up to 19.6 million encoder pulses per second
    • Position control with analog encoders or potentiometers
    • (Open-loop control with no feedback also available)
  • Screw terminals for quick connect/disconnect
  • Configurable via pushbutton interface
  • Regenerative braking
  • Tolerates high-speed direction changes
  • Jumper-selectable 5 V BEC
  • Battery monitoring and under-voltage cutoff protects batteries from over-discharging

RoboClaw Comparison Table




ST 2x45A

Motor channels:2
Operating voltage:6 V to 34 V
Continuous output current:7.5 A15 A30 A45 A60 A
Peak output current:15 A30 A60 A60 A120 A
5V BEC(1) max current:150 mA3 A
Width:1.7? (4.2 cm)2.1? (5.2 cm)3.4? (8.6 cm)
Length:1.9? (4.8 cm)2.9? (7.4 cm)3.9? (10 cm)
Weight:17 g60 g60 g (2x45A)
63 g (ST 2x45A)
205 g

1 Battery Eliminator Circuit

Sample Code

Ion Motion Control has written an Arduino library for the RoboClaw that makes it easy to interface these motor controllers with an Arduino. The library comes with several example sketches that demonstrate different methods of controlling the RoboClaw.

Note: Ion Motion Control was formerly Orion Robotics, which was previously Basic Micro. Ion Motion Control uses the following product names and number for the RoboClaw controllers:

    ?RoboClaw 2x7A Motor Controller?, Item Id: ION404 (replaces ?RoboClaw 2x5A?, Item Id: ION403)
    ?RoboClaw 2x15A Motor Controller?, Item Id: ION412
    ?RoboClaw 2x30A Motor Controller?, Item Id: ION413
    ?RoboClaw 2x45A Motor Controller?, Item Id: ION418
    ?RoboClaw ST 2x45A Motor Controller?, Item Id: ION419
    ?RoboClaw 2x60A Motor Controller?, Item Id: ION414

Artikelgewicht:0,21 Kg

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

Frage zum Produkt

Frage zum Produkt
max. 500 Zeichen