Adafruit Stereo 3.7W Class D Audio Amplifier - MAX98306

Artikelnummer: AF987

Kategorie: Amplifiers/Sound


10,65 €

inkl. 19% USt.,

3 bestellt, am 26.06.2018 erwartet

Lieferfrist: ca. 6 - 8 Tage

Stk


Beschreibung

Overview

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving an 8O speaker at over a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. This board is a welcome upgrade to basic "LM386" amps! 

The inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the R- and L- to ground. The outputs are "Bridge Tied" - that means they connect directly to the outputs, no connection to ground. The output is a 360KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. 
Comes with a fully assembled and tested breakout board with 1.0uF input capacitors. We also include header to plug it into a breadboard, 3.5mm screw-terminal blocks so you can easily attach/detach your speakers, and a 2x4 header + jumper to change the amplifier gain on the fly. You will be ready to rock in 15 minutes! Speakers are not included, use any 3ohm or greater impedance speakers. 
  • Output Power: 3.7W at 3O, 10% THD, 1.7W at 8O, 10% THD, with 5V Supply
  • Passes EMI limit unfiltered with up to 12 inches (30 cm) of speaker cable
  • High 83dB PSRR at 217Hz
  • Spread-Spectrum Modulation and Active Emissions Limiting
  • Five pin-selectable gains: 6dB, 9dB, 12dB, 15dB and 18dB. Select with a jumper or by setting the G and G' breakout pins (see schematic for breakout board showing gain pin settings for details)
  • Excellent click-and-pop suppression
  • Thermal and short-circuit/over-current protection
  • Low current draw: 2mA quiescent and 10uA in shutdown mode

Technical Details:

Dimensions (without 0.1" header): 
  • Length:28.25mm/1.11in
  • Width:24.15mm/0.95in
  • Height:3.03mm/0.12in
  • Weight:2.33g

Package list

1x Adafruit Stereo 3.7W Class D Audio Amplifier - MAX98306

Dokumente

Bedienungsanleitung

MAX98306 Datasheet

Fritzing object in Adafruit Fritzing library

EagleCAD PCB files on GitHub

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

----

Diese Modul passt zu folgende Produkten:
2pcs 40mm Bass Multimedia Lautsprecher 3W 4Ohm Audio... 2pcs 40mm Bass Multimedia Lautsprecher 3W 4Ohm Audio...
sofort verfügbar
2pcs 40mm Bass Multimedia Lautsprecher 3W 4Ohm Audio... 2pcs 40mm Bass Multimedia Lautsprecher 3W 4Ohm Audio...
sofort verfügbar
2pcs 45mm Bass Multimedia Lautsprecher 5W 4Ohm Audio... 2pcs 45mm Bass Multimedia Lautsprecher 5W 4Ohm Audio...
sofort verfügbar
Kunden kauften dazu folgende Produkte
2pcs 50mm Bass Multimedia Lautsprecher 5W 4ohm Audio... 2pcs 50mm Bass Multimedia Lautsprecher 5W 4ohm Audio...
Lange Lieferzeit beachten!
Jumper Wire 10x1P female to female 20cm
sofort verfügbar
Adafruit VS1053 Codec + MicroSD Breakout - MP3 WAV MIDI... Adafruit VS1053 Codec + MicroSD Breakout - MP3 WAV MIDI...
2 bestellt, am 26.06.2018 erwartet
Adafruit Mono 2.5W Class D Audio Amplifier - PAM8302 Adafruit Mono 2.5W Class D Audio Amplifier - PAM8302
sofort verfügbar
Jumper Wire 10x1P female to male 20cm Jumper Wire 10x1P female to male 20cm
sofort verfügbar
Jumper Wire 10x1P male to male 20cm
sofort verfügbar