Adafruit Push-button Power Switch Breakout

Artikelnummer: AF1400

Kategorie: Energieversorgungsmodul


5,98 €

inkl. 19% USt.,

sofort verfügbar

Lieferzeit: 1 bis 2 Tage

Stk


Beschreibung

The Adafruit Push-button Power Switch is a tidy little design that lets you control a DC power source using an everyday tactile button. The breakout uses a latching analog circuit that is triggered by a push of the button. Press once to tu on, then press again to tu off. The circuit uses a 3A P-FET to connect and disconnect the IN pin to the OUT pin. Works great from 3V to 14VDC and up to 3A (although the FET gets a little toasty at continuous 3A draw) yet has only 0.5uA quiescent current draw.

Using it is easy: connect the power source to Ground and IN, then the load from Ground to OUT. We include a 12mm tactile switch that works well but you can solder in your own switch as well. Press the button (or short the button pins) to alteate between on or off. A on-board red LED will light up when active so you know its working. There's a fourth KILL pin, which you can use to tu off the load and/or keep it off even if the button is pressed. When 1 or more volts is applied it will instantly tu off the FET. This allows your project to tu itself off.

Comes with a assembled & tested bread-board friendly breakout board with four mounting holes, a 12mm tactile button, and some 0.1" male header you can solder to the board to plug it into a breadboard.

he power switch is an elegant way to control power to your project, but there are some things to keep in mind: since there is a pass FET, this is only for 3-14V DC voltages. This is not a mechanical switch so there is no air-gap isolation. There is a 'body diode' in the pass FET so if the load has a voltage on it that is higher than the input voltage, current will flow back to the input. There is built-in debouncing but very bouncy switches can be annoying as they will tu on and off fast instead of latching.

Adafruit Push-button Power Switch Breakout (11:52)

Technical Details


Artikelgewicht: 0,00 Kg

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

Frage zum Produkt

Kontaktdaten
Frage zum Produkt
max. 500 Zeichen

Kunden kauften dazu folgende Produkte
Pololu Mini Pushbutton Power Switch with Reverse Voltage... Pololu Mini Pushbutton Power Switch with Reverse Voltage...
sofort verfügbar
HC-SR501 PIR Infrarot Bewegungsmelder Motion Sensor Modul... HC-SR501 PIR Infrarot Bewegungsmelder Motion Sensor Modul...
sofort verfügbar
Adafruit Feather M0 Adalogger Adafruit Feather M0 Adalogger
sofort verfügbar
0.1 (2.54mm) Crimp Connector Housing: 2x4-Pin 10-Pack 0.1 (2.54mm) Crimp Connector Housing: 2x4-Pin 10-Pack
sofort verfügbar
Jumper Wire 10x1P female to female 20cm
sofort verfügbar
FeatherWing OLED - 128x32 OLED Add-on For All Feather Boards FeatherWing OLED - 128x32 OLED Add-on For All Feather Boards
sofort verfügbar
0.1 (2.54mm) Crimp Connector Housing: 1x5-Pin 10-Pack 0.1 (2.54mm) Crimp Connector Housing: 1x5-Pin 10-Pack
sofort verfügbar
8-Digit LED Display Digital Tube Red 74HC595 for Arduino 8-Digit LED Display Digital Tube Red 74HC595 for Arduino
sofort verfügbar
2x 2x40Pin 2.54mm Double Row Pin Header Strip 2x 2x40Pin 2.54mm Double Row Pin Header Strip
sofort verfügbar
Makeblock Silicone Air Tube 0305 Makeblock Silicone Air Tube 0305
sofort verfügbar
Adafruit NeoPixel Jewel - 7 x 5050 RGBW LED w  Integrated... Adafruit NeoPixel Jewel - 7 x 5050 RGBW LED w  Integrated...
sofort verfügbar
Waveshare FT232 USB TO UART solution with USB micro... Waveshare FT232 USB TO UART solution with USB micro...
sofort verfügbar