Adafruit PowerBoost 1000 Basic - 5V USB Boost @ 1000mA from 1.8V+

Artikelnummer: AF2030

EAN: 4060137024542

Hersteller-Artikelnr.: 2030

Kategorie: Energieversorgungsmodul


13,48 €

inkl. 19% USt.,

sofort verfügbar

Lieferzeit: 1 bis 2 Tage

Stk


Beschreibung

Details

PowerBoost is the perfect power supply for your power-hungry portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your 5V projects. With a beefy 4A DC/DC converter, it can give you 1A+ from as low as 2V. 

We tweaked the output to be 5.2V instead of a straight-up 5.0V so that there's a little bit of 'headroom' long cables, high draw, the addition of a diode on the output if you wish, etc. The 5.2V is safe for all 5V-powered electronics like Arduino, Raspberry Pi, or Beagle Bone while preventing icky brown-outs during high current draw because of USB cable resistance.

The PowerBoost 1000 has at the heart a TPS61030 boost converter from TI. This boost converter chip has some really nice extras such as low battery detection, 4A internal switch, synchronous conversion, excellent efficiency, and 700KHz high-frequency operation. Check out these specs!
  • Synchronous operation means you can disconnect the output completely by connecting the ENable pin to ground. This will completely turn off the output
  • 4A internal switch means you can get 1000mA+ from as low as 1.8V, 1500mA+ from 2 NiMH or Alkaline batteries, and at least 2000mA from a 3.7V LiPoly/LiIon battery or 3 NiMH/Alkalines. Just make sure your batteries can actually supply the required 2-4A, OK?
  • Low battery indicator LED lights up red when the voltage dips below 3.2V, optimized for the most common usage of LiPo/LiIon battery usage
  • On-board 1000mA charge-rate 'Apple/iOS' data resistors. Solder in the included USB connector and you can plug in any iPhone or iPod for a speedy 1000mA charge rate. Works with iPads, both mini and 'classic' type.
  • Full breakout for battery in, control pins and power out
  • 90%+ operating efficiency in most cases (see datasheet for efficiency graphs), and low quiescent current: 5mA when enabled and power LED is on, 20uA when disabled (power and low batt LED are off)

Great for powering your robot, Arduino project, single-board-computer such as Raspberry Pi or BeagleBone! Each order comes with one fully assembled and tested PCB, a loose 2-PH JST jack, a 2-pin Terminal block and a loose USB A jack.

If you are powering your project from USB, solder the USB A jack in (a 3-minute soldering task). Then choose either JST for input (JST is often used for our LiIon batteries, but the connector is only rated for 2A) or a terminal block. 

The 1000 version comes with a 2-pin terminal block so you can solder it to the output spot where the USB jack would go. Or don't solder any connectors in for a more compact power pack and go with 22AWG wires soldered directly in.


Technical Details:

  • Dimensions: 29mm x 23mm x 2mm / 1.1" x .9" x .1"
  • Height w/ JST: 7.5mm / .30"
  • Weight: 6.0g
  • Hey there's a typo on the back, it says TPS61090 but we really use the TPS61030 - the '90 is the 2A version, the '30 is the 4A version! We'll fix on the next PCB run. Read more about the TPS61030 boost converter from TI here


Learn:

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

Frage zum Produkt

Kontaktdaten
Frage zum Produkt
max. 500 Zeichen

Diese Modul passt zu folgende Produkten:
PKCELL LiPo Akku Lithium-Ion Polymer Batterie 3,7V... PKCELL LiPo Akku Lithium-Ion Polymer Batterie 3,7V...
sofort verfügbar
PKCELL LiPo Akku Lithium-Ion Polymer Batterie 3,7V... PKCELL LiPo Akku Lithium-Ion Polymer Batterie 3,7V...
sofort verfügbar
Kunden kauften dazu folgende Produkte
PKCELL LiPo Akku Lithium-Ion Polymer Batterie 3,7V... PKCELL LiPo Akku Lithium-Ion Polymer Batterie 3,7V...
sofort verfügbar
Pololu Mini Pushbutton Switch: PCB-Mount, 2-Pin, SPST,... Pololu Mini Pushbutton Switch: PCB-Mount, 2-Pin, SPST,...
sofort verfügbar
Adafruit USB Micro-B Breakout Board Adafruit USB Micro-B Breakout Board
Lange Lieferzeit beachten!
Adafruit INA169 Analog DC Current Sensor Breakout - 60V... Adafruit INA169 Analog DC Current Sensor Breakout - 60V...
sofort verfügbar
Adafruit PowerBoost 500 Basic - 5V USB Boost @ 500mA from... Adafruit PowerBoost 500 Basic - 5V USB Boost @ 500mA from...
sofort verfügbar
Adafruit VERTER 5V USB Buck-Boost - 500mA from 3V-5V... Adafruit VERTER 5V USB Buck-Boost - 500mA from 3V-5V...
sofort verfügbar